国产一区二区在线观看,亚洲av无码99久久久国精,国产边添边摸边做边爱,日本久久久久久久做爰片日本

產品展示
首頁 > 產品展示 > > 其他檢測儀器 > TC-500 氧氮聯合測定儀

TC-500 氧氮聯合測定儀

簡要描述：簡單說明：TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

  • 產品型號：TC-500
  • 廠商性質：生產廠家
  • 更新時間：2024-10-08
  • 訪  問  量：2216
詳情介紹

詳細說明:

TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

Determination of Oxygen and Nitrogen in
Reactive/Refractory Metals and Their Alloys*
 
Approval
ASTM E-1409 Oxygen Determination in Titanium and Titanium Alloys
ASTM E-1569 Oxygen Determination in Tantalum
ASTM E-1937 Nitrogen Determination in Titanium and Titanium Alloys
 
Sample Preparation
A clean representative sample is required in order to obtain optimum results. Solid samples can be leached in suitable acid or abraded with a clean file, rinsed in acetone, and dried with warm air. Refer to ASTM methods above for further details.
 
Accessories
782-720 Crucible; 782-721 Electrode Tip; 502-344 UHP Nickel
Baskets; 501-073 Graphite; 503-032 Glass Accelerator Scoop;
501-059 Tin Capsules—for powdered samples. （Additional steps required for powdered samples are noted in parenthesis.）
 
Calibration Standard
LECO 501-320 Titanium Pin, 502-047 Zirconium Pin, NIST, or other suitable reactive/refractory metal standard.
 
Method Parameters
Analysis Parameters
Outgas Cycles                           2
Analysis Delay （seconds）             20
Analysis Comparator                 1
Analysis Type                              Auto
 
Element Parameters                  Oxygen           Nitrogen
Minimum Time （seconds）
35
55
Integration Delay （seconds）
5
15
Comparator Level （%）
1
1
 
Furnace Parameters
Furnace Control Mode             Power
Purge Time （seconds）                    15
Outgas Time （seconds）                20
Cool Time （seconds）                    5
Outgas Power （Watts）                 6300
Analyze Power （Watts）                5300
 
 
 
 
 


 

*This includes Ti, Zr, W, Mo, Ta, Nb, Hf, and their alloys.

 
TC500


 

 
Typical Results
 
 
 
Titanium Pin
Mass （g）
Oxygen （%）
Nitrogen （%）
 
0.1135
0.1808
0.0189
 
0.1133
0.1843
0.0194
 
0.1134
0.1831
0.0184
 
0.1138
0.1819
0.0188
 
0.1133
0.1821
0.0195
 
0.1131
0.1829
0.0185
 
0.1134
0.1833
0.0191
 
0.1143
0.1849
0.0194
 
0.1125
0.1837
0.0189
 
0.1072
0.1830
0.0191
 
Average
0.1830
0.0190
 
Std. Dev.
0.0012
0.0004
 
Zirconium Wire
 
Mass （g）
 
Oxygen （%）
 
Nitrogen （%）
 
0.1067
0.1246
0.0017
 
0.0978
0.1273
0.0017
 
0.1180
0.1246
0.0019
 
0.1097
0.1235
0.0014
 
0.1141
0.1272
0.0017
 
0.1017
0.1226
0.0018
 
0.1140
0.1269
0.0020
 
0.0987
0.1239
0.0020
 
0.1015
0.1233
0.0022
 
0.1197
0.1270
0.0020
 
Average
0.1251
0.0018
 
Std. Dev.
0.0018
0.0002
 
Procedure
 
 
 
1.   Determine the blank as follows:
a.   Enter the "blank" ID code with a 1.0000 g weight in the weight stack.
b.   Press the loader control switch, the sample loader will open.
c.   Place one 502-344 UHP Nickel basket into the loading head using clean tweezers.
（Place a 501-059 Tin capsule into the Nickel basket before placing it in the loading head.）
d.   Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
e.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
f.    Place ~0.05 g 501-073 into the bottom of a 782-720 crucible.  ~0.05 g is approximay a ¼ full
503-032 glass accelerator scoop.
g.   Place the crucible on the lower electrode.
h.   Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
i.    Repeat steps 1a through 1h at least four more times.
j.    Enter blank following routine outlined in operator's instruction manual.
2.   Calibrate the instrument as follows:
a.   Weigh the calibration sample. （Weigh the calibration sample into the tin capsule.）
b.   Enter the calibration sample ID code and sample weight in the weight stack.
c.   Place the calibration sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the calibration sample/nickel basket （capsule） into the loading head using clean tweezers.  Make sure that the calibration sample （capsule） stays in the basket and the basket
stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
continued on page 3


 

Procedure （continued from page 2）
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
k.   Repeat steps 2a through 2j a minimum of three times.
l.    Complete a calibration by following the auto calibration procedure as outlined in the operator's instruction manual.
m.  Verify the calibration by analyzing the calibration sample again.  It should fall within the expected tolerances.  If not, repeat steps 2a through 2l again.
3.   Analyze the samples as follows:
a.   Weigh ~0.1 g sample. （Weigh the sample into the tin capsule.）
b.   Enter the sample ID code and sample weight in the weight stack.
c.   Place the sample （capsule） into a nickel basket.
d.   Press the loader control switch, the sample loader will open.
e.   Carefully place the sample/nickel basket （capsule） into the loading head using clean tweezers.
Make sure that the sample （capsule） stays in the basket and the basket stays upright.
f.    Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.
g.   Remove crucible from electrode tip and discard.  Clean furnace area using the appropriate brushes.  Vacuum away loose dust.
h.   Place ~0.05 g graphite into the bottom of a crucible.
i.    Place the crucible on the lower electrode.
j.    Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.
 
Theory of Operation
The TC500 is a microprocessor-based, software-controlled instrument that measures both nitrogen and oxygen in a wide variety of metals, refractories, and inorganic materials. The inert gas fusion principle is employed. A weighed sample, placed in a high-purity graphite crucible, is fused under a flowing helium gas stream at temperatures sufficient to release oxygen, nitrogen, and hydrogen. The oxygen in the
sample, combines with the carbon from the crucible to form carbon monoxide. The nitrogen present in
the sample releases as molecular nitrogen, and any hydrogen present is released as hydrogen gas. The helium carries the sample gases through heated rare earth copper oxide which converts carbon
monoxide to carbon dioxide （CO2） and hydrogen to water （H2O）. The nitrogen passes through
unchanged. The gases are then passed through a CO2  infrared （IR） cell where the oxygen is measured as
CO2. CO2  and H2O are then removed by a Lecosorb/Anhydrone trap, while the nitrogen passes through
to a thermal conductivity （TC） cell for determination.


 

TC500 Flow Diagram
 
 
 
 
 

留言框

  • 產品：

  • 您的單位：

  • 您的姓名：

  • 聯系電話：

  • 常用郵箱：

  • 省份：

  • 詳細地址：

  • 補充說明：

  • 驗證碼：

    請輸入計算結果（填寫阿拉伯?dāng)?shù)字），如：三加四=7

技術支持：化工儀器網   sitemap.xml   管理登陸
©2025 版權所有：寧波市鄞州瑾瑞儀器設備有限公司   備案號：浙ICP備14028217號-3

浙公網安備33020402000311號
久久国产精品偷| 真人做人试看60分钟免费视频| 爽欲亲伦96部分| 免费网站安全软件大全| 亚洲精品午夜国产va久久成人| 无码人妻丰满熟妇啪啪网站牛牛| 18款禁用免费安装的软件app| 国产精品永久久久久久久久久| 波多野结衣中文| 日本japanese熟睡人妻| 日韩av人妻无码heyzo专区| chinese农村老妓女| 亚洲av无码乱码国产麻豆| 少妇高潮毛片色欲AVA片| 人妻无码αv中文字幕久久琪琪布| 少妇与大狼拘作爱| 边啃奶头边躁狠狠躁视频免费观看| 97精品国产97久久久久久免费| 免费真人视频网站| 免费又黄又爽又猛的毛片| 曰曰摸日日碰夜夜爽歪歪| 中文字幕爆乳巨爆乳系列| 年轻护士的滋味中文字幕| 久久精品人妻少妇一区二区三区| 豪妇荡乳1一5潘金莲| 国产性生交xxxxx免费| 初六苏梅全文免费阅读正版| 欧洲aaaaa特级毛片| 久久久久人妻一区精品色| 亚洲色大成网站www| 辽宁少妇高潮45分钟| 久久中文字幕人妻熟av女蜜柚m| 国产成人a亚洲精v品无码| 成人做爰www网站视频| 国产欧美一区二区三区在线看| 亚洲日本va中文字幕久久道具| 欧美r级a片成人片不可撤销| 日本xxxx高清色视频在线播放| 中文字幕人妻紧无码专区| 两片大荫唇之间已经湿漉漉的一片| 久久兔费黄a级毛片高清|